Projects & Products

Showing 41–56 of 56 results

  • XNL ISP Speed Flash Board (Add-on!)

    XNL ISP Speed Flash Board (Add-on!)

    A simple add-on for the XNL LABUNO Overkill Edition which enables you to quickly and easily flash and/or boot-load a wide range of AVR microcontrollers by simply using your XNL LABUNO Overkill Edition’s AVR/ISP Programmer header

    Microcontrollers supported by this board
    – ATmega 48, 88, 168 & 328 (28 pin)
    – ATmega 644 & 1284 (40 Pin)
    – Tiny 2313 (20 Pin)
    – Tiny 44 & 84 (14 pin)
    – Tiny 45 & 85 (8 pin)

    Download Size: 1.6mb

  • XNL LABUNO

    XNL LABUNO

    The XNL LABUNO is ‘our answer’ to the Arduino® Uno, but with (much) more control over your hardware.

    Some of the features you have full control over with the LABUNO are:
    – Pull-up resistors on the ‘reset-line’
    – Enable/Disable RTS Reset
    – Switch TTL communication between HW / SW
    – VCC source selection
    – High power LM3940 3.3V Regulator
    – Full control over the serial pins
    – Build-in support for ESP board (and communication)

    Next to these (and more) features, the headers (next to the microcontroller) also ‘line-up’ 1:1 with the microcontroller pin-out.

    NOTE:
    This model requires an USB->TTL adapter like for example the XNL F.U.T.S. or an FTDI cable to communicate with your computer. The LABUNO USB has an onboard USB-Serial chip and thus does not need an additional USB adapter/cable. We also have the LABUNO Overkill Edition which has even more ‘on-board’ features and also has an onboard USB controller.

    “Multi Pack” NOTE:
    This download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.

    Download Size: 4mb

  • XNL LABUNO Overkill Edition

    XNL LABUNO Overkill Edition

    The XNL LABUNO Overkill Edition is an ‘expanded version’ of our XNL LABUNO USB.

    Some of the features you have full control over with the LABUNO are:
    – Pull-up resistors on the ‘reset-line’
    – Enable/Disable RTS Reset
    – Switch TTL communication between HW / SW
    – VCC source selection
    – High power LM3940 3.3V Regulator
    – Full control over the serial pins
    – Build-in support for ESP board (and communication)

    Additional Features with the LABUNO Overkill Edition:
    – Full access to ALL serial/UART pins
    – Three onboard Ready to use Servo Ports
    – I2C/OLED LCD Header Ready to use
    – Onboard AVR/ISP Programmer using the
    Arduino as ISP sketch.

    Next to these (and more) features, the headers (next to the microcontroller) also ‘line-up’ 1:1 with the microcontroller pin-out.

    NOTE:
    This has it’s own ‘onboard’ USB to serial (TTL) chip (the CH340G), while the LABUNO does not have any USB controller/chip onboard. So if you prefer to choose your own USB->Serial chip, we would like you to recommend to check out the LABUNO instead. We also have the XNL LABUNO USB which is a bit more ‘subtle’ so to speak.

    “Multi Pack” NOTE:
    The (NON USB) XNL LABUNO download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.

    Download Size: 4.5mb

  • XNL LABUNO USB

    XNL LABUNO USB

    The XNL LABUNO USB is ‘our answer’ to the Arduino® Uno, but with (much) more control over your hardware.

    Some of the features you have full control over with the LABUNO are:
    – Pull-up resistors on the ‘reset-line’
    – Enable/Disable RTS Reset
    – Switch TTL communication between HW / SW
    – VCC source selection
    – High power LM3940 3.3V Regulator
    – Full control over the serial pins
    – Build-in support for ESP board (and communication)

    Next to these (and more) features, the headers (next to the microcontroller) also ‘line-up’ 1:1 with the microcontroller pin-out.

    NOTE:
    This has it’s own ‘onboard’ USB to serial (TTL) chip (the CH340G), while the LABUNO does not have any USB controller/chip onboard. So if you prefer to choose your own USB->Serial chip, we would like you to recommend to check out the LABUNO instead. We also have the LABUNO Overkill Edition which has even more ‘on-board’ features and also has an onboard USB controller.

    “Multi Pack” NOTE:
    The (NON USB) XNL LABUNO download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.

    Download Size: 3.8mb

  • XNL Logic Monitor Module (for LABUNO and LABUNO USB)

    XNL Logic Monitor Module (for LABUNO and LABUNO USB)

    The XNL Logic Monitor is a small ‘add-on’ for the XNL LABUNO and XNL LABUNO USB which can add an RX and TX LED for the UART (Serial) ports of the LABUNO’s.

    The XNL LABUNO’s don’t have their own RX and TX LED’s “onboard” to keep the ‘lines as clear as possible’. Therefor we also decided to use the ‘opamp method’ to ensure minimal ‘additional load’ on the (data) lines.

    These boards can be used for both the hardware and/or software serial ports of the LABUNO’s

    “Multi Pack” NOTE:
    The (NON USB) XNL LABUNO download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.

    Download Size: 645kb

  • XNL Microscope Adapter (for Microphone Arm)

    XNL Microscope Adapter (for Microphone Arm)

    I love my cheap Chinese AliExpress (Electronics) microscope, but it just drove me absolutely bonkers when I tried to use it with larger boards.

    So I decided to design as small (3D Printed) adapter which uses a 3/8″ thread, so that the cheap Microscope could be placed on a microphone arm, basically giving it the same flexibility as the (much) more expensive electronics lab microscopes but for a much lower price (for me totaling around €65,-)

    I made a YouTube video about this project here

    Download: 2.1mb
    P/N: XLT290724

  • XNL Mini SIM Adapter

    XNL Mini SIM Adapter

    The XNL Mini SIM Adapter is a very simple to assemble product which will make it very easy to interface directly with (mobile) SIM Cards on your breadboard.

    Perfect for when you are building a SMS, GPRS, 3G, 4G or other ‘Mobile Telecom’ project on your breadboard with a module which doesn’t have it’s own SIM Card slot.

    NOTE:
    This project/product has no datasheet/manual in the download! The instructions are listed bellow in the information tabs.

    Download Size: 123kb

  • XNL Protoboard A 100x100mm (38x36)+36P 1404 Holes

    XNL Protoboard A 100x100mm (38×36)+36P 1404 Holes

    This is our 100x100mm (10x10cm) XNL Protoboard XPB5722-A.

    There are two versions, this one which has ‘small ground planes’ between each hole and along it’s edges. and the XPB5722-A1 which doesn’t have these ‘ground planes’
    For most users we would recommend using the XPB5722-A1 instead!

    Specifications:
    Size: 100x100mm
    Holes: 1404 (38×36)+36
    Spacing: 2.54mm / 0.1”
    Model: (38×36)+36P
    P/N: XPB5722-A

    Download Size: 307kb

  • XNL Protoboard A1 100x100mm (38x36)+36 1404 Holes

    XNL Protoboard A1 100x100mm (38×36)+36 1404 Holes

    This is our 100x100mm (10x10cm) XNL Protoboard XPB5722-A.

    There are two versions, this one and the XPB5722-A which has ‘small ground planes’ between each hole and along it’s edges.
    This is the model/version which we would recommend for most users.

    Specifications:
    Size: 100x100mm
    Holes: 1404 (38×36)+36
    Spacing: 2.54mm / 0.1”
    Model: (38×36)+36
    P/N: XPB5722-A1

    Download Size: 88kb

  • XNL SpySIM

    XNL SpySIM

    Ever “needed” to hook-up some wires to the ‘SIM Card Socket’ of a mobile phone for one of your ‘Sketchy Projects’, but didn’t wanted to solder wires onto the ‘pins’?

    Well then maybe this little board might be just what you need for those ‘sketchy SIM Port Projects’ ;)

    Download Size: 17kb

  • XNL STAR-3

    XNL STAR-3

    The XNL STAR-3 is our own ‘answer’ on the commonly known (Chinese) BluePill development board.

    The XNL STAR-3 is an (72MHz) ARM® Cortex®-M3 based development board, developed to offer a more ‘developer friendly’ experience than with the commonly used (Chinese) Blue Pill boards.

    Quick Overview Specs:
    • 72MHz ARM® 32-bit Cortex®-M3
    • 64KB or 128KB Flash (program) Memory
    • 20KB SRAM
    • RTC (With onboard battery)

    Download Size: 2.5MB

  • XNL STAR-3-MB

    XNL STAR-3-MB

    The XNL STAR-3-MB is basically a ‘motherboard’ for the commonly known (Chinese) BluePill development boards.

    While at the same time also providing a very easy, fast and convenient way to ‘snap-in-and-flash’ (bootload) your BluePill board without needing additional USB->Serial boards or other flash tools/sticks.

    During development the XNL STAR-3-MB also gives you instant access to the USB port of the BluePill itself, an additional USB port which functions as a USB->Serial adapter for TX1 & RX1, an onboard RTC Battery and a (more stable) 3.3V ‘power supply’ for your external 3.3V components and/or modules.

    Download: 2.5MB

  • XNL STAR-3(-MB) Bootloader Bin

    XNL STAR-3(-MB) Bootloader Bin

    This is our mirror of the XNL STAR-3 Bootloader bin file.

    This bootloader can (also) be used for:
    – XNL STAR-3 Boards
    – XNL STAR-3-MB Boards
    – STM32 Blue Pill boards
    – Most other boards using an STM32F103C8
    – Most other boards using an STM32F103CB

    IMPORTANT NOTE:
    This is a backup mirror to ensure that you always have access to the version/bootloader which we recommend. Make sure to check the Information Tab to see if the original author has a more recent version!

    Download Size: 13KB

  • XNL STAR-3(-MB) Drivers

    XNL STAR-3(-MB) Drivers

    These are a mirror of the (USB) drivers for the XNL STAR-3 and several other STM32 based boards.

    These drivers can also be used for:
    – XNL STAR-3-MB Boards
    – STM32 Blue Pill boards
    – Most other boards using an STM32F103C8
    – Most other boards using an STM32F103CB

    Download Size: 22MB

  • XNL TextSpec 3.0

    XNL TextSpec 3.0

    20 years ago (as of 2024) I wrote TextSpec 2.0B which was used to count words, characters and lines in a pasted (plain) text. Simply because lots of people I knew back then didn’t had Microsoft Word on their home computer, or they just wanted a small (quickly starting) tool to get this information about a piece of text fast and efficiently.

    In honor of the 20 year old version I decided to completely rewrite TextSpec from scratch in .NET with a lot more features, accuracy and other improvements.

    Interested in what this new modernized version has to offer and why I decided to rewrite it again? Make sure to check the information bellow for more details 😊

    Download: 396KB (Program/Binaries)
    Download: 470KB (Source Code)

  • XNL Wesp (ESP8266 WIFI)

    XNL Wesp (ESP8266 WIFI)

    The XNL WESP is our (simple) solution to work with the ESP-12E boards using our XNL LABUNO’s. It basically ‘converts’ your ESP-12E modules into a ‘mini development board’ when used in combination with our LABUNO’s.

    This is however not a full (stand-alone) development board, officially put this is ‘just a breakout board’!

    NOTE: The download for the XNL WESP also contains the official datasheet of the ESP-12E

    “Multi Pack” NOTE:
    The (NON USB) XNL LABUNO download also contains a panelized version of the XNL LABUNO which includes two XNL Logic Monitors, an XNL ESP Direct Board, and an XNL WESP Board which means that it might actually be cheaper to order the panelized version (if your PCB Manufacturer allows pre-panelized boards) if you need or want all modules.